No plot window on Mac El Capitan
Hi Bruce, I just upgraded my mac from mountain lion to el capitan. I was using the old version, iXAFS, but I can't launch it on the new el capitan. I then installed Demeter with Macport by following the instructions. However, I'm not able to plot the data in athena and artemis. I read the thread about "no plot window on Yosemite", but still have no clue. I can plot gnuplot in aqua, x11 and wxt. It seems whenever I quit gnuplot to launch athena and enter gnuplot later again, it will always go back my default terminal, aqua, no matter how I set terminal. Is there a communication problem between Demeter and aqua? I'm not familiar with these commands, to be honest. If I did something wrong, please advise. Thanks, Chloe -- Yi-Yi (Chloe) Wu Kung Research Group Dept. of Chemical and Biological Engineering Northwestern University Evanston, IL USA
On 10/07/2015 01:26 PM, Chloe Yi-Yi Wu wrote:
Hi Bruce,
I just upgraded my mac from mountain lion to el capitan. I was using the old version, iXAFS, but I can't launch it on the new el capitan. I then installed Demeter with Macport by following the instructions. However, I'm not able to plot the data in athena and artemis.
I read the thread about "no plot window on Yosemite", but still have no clue. I can plot gnuplot in aqua, x11 and wxt. It seems whenever I quit gnuplot to launch athena and enter gnuplot later again, it will always go back my default terminal, aqua, no matter how I set terminal. Is there a communication problem between Demeter and aqua? I'm not familiar with these commands, to be honest. If I did something wrong, please advise.
I believe this is the same as the problem addressed here: http://millenia.cars.aps.anl.gov/pipermail/ifeffit/2015-September/012703.htm... It will be fixed whenever the next version gets built for MacPorts. George offers a work-around here: http://millenia.cars.aps.anl.gov/pipermail/ifeffit/2015-September/012739.htm... B
Thanks, Chloe
-- Yi-Yi (Chloe) Wu Kung Research Group Dept. of Chemical and Biological Engineering Northwestern University Evanston, IL USA
_______________________________________________ Ifeffit mailing list Ifeffit@millenia.cars.aps.anl.gov http://millenia.cars.aps.anl.gov/mailman/listinfo/ifeffit
-- Bruce Ravel ------------------------------------ bravel@bnl.gov National Institute of Standards and Technology Synchrotron Science Group at NSLS-II Building 535A Upton NY, 11973 Homepage: http://bruceravel.github.io/home/ Software: https://github.com/bruceravel Demeter: http://bruceravel.github.io/demeter/
On 10/07/2015 02:05 PM, Bruce Ravel wrote:
George offers a work-around here:
http://millenia.cars.aps.anl.gov/pipermail/ifeffit/2015-September/012739.htm...
Also relevant: http://millenia.cars.aps.anl.gov/pipermail/ifeffit/2015-September/012742.htm... -- Bruce Ravel ------------------------------------ bravel@bnl.gov National Institute of Standards and Technology Synchrotron Science Group at NSLS-II Building 535A Upton NY, 11973 Homepage: http://bruceravel.github.io/home/ Software: https://github.com/bruceravel Demeter: http://bruceravel.github.io/demeter/
Hi Bruce, I don't find "athena preferences menu" when I open athena... I can only see "service preferences" under perl5.22, which is the preferences for my mac not for athena... I just found if I set terminal to qt, it showed "unknown". If I set to x11, it showed "nopersist enhanced". If I set to wxt, it showed "0 enhanced". Are these normal? Thanks, Chloe On Wed, Oct 7, 2015 at 12:26 PM, Chloe Yi-Yi Wu < yiyiwu2016@u.northwestern.edu> wrote:
Hi Bruce,
I just upgraded my mac from mountain lion to el capitan. I was using the old version, iXAFS, but I can't launch it on the new el capitan. I then installed Demeter with Macport by following the instructions. However, I'm not able to plot the data in athena and artemis.
I read the thread about "no plot window on Yosemite", but still have no clue. I can plot gnuplot in aqua, x11 and wxt. It seems whenever I quit gnuplot to launch athena and enter gnuplot later again, it will always go back my default terminal, aqua, no matter how I set terminal. Is there a communication problem between Demeter and aqua? I'm not familiar with these commands, to be honest. If I did something wrong, please advise.
Thanks, Chloe
-- Yi-Yi (Chloe) Wu Kung Research Group Dept. of Chemical and Biological Engineering Northwestern University Evanston, IL USA
-- Yi-Yi (Chloe) Wu Kung Research Group Dept. of Chemical and Biological Engineering Northwestern University Evanston, IL USA
On 10/08/2015 01:53 PM, Chloe Yi-Yi Wu wrote:
Hi Bruce,
I don't find "athena preferences menu" when I open athena... I can only see "service preferences" under perl5.22, which is the preferences for my mac not for athena...
I just found if I set terminal to qt, it showed "unknown". If I set to x11, it showed "nopersist enhanced". If I set to wxt, it showed "0 enhanced". Are these normal?
I don't know what any of that means -- I have no clue what you are referring to in either paragraph. Here's what George was referring to: http://bruceravel.github.io/demeter/aug/other/prefs.html Click to open the gnuplot branch, click on terminal, type in your choice of terminal type, click on save and apply. B -- Bruce Ravel ------------------------------------ bravel@bnl.gov National Institute of Standards and Technology Synchrotron Science Group at NSLS-II Building 535A Upton NY, 11973 Homepage: http://bruceravel.github.io/home/ Software: https://github.com/bruceravel Demeter: http://bruceravel.github.io/demeter/
participants (2)
-
Bruce Ravel -
Chloe Yi-Yi Wu