Hi Nirawat,
I think I may know what’s happening with your
laptop. You said:
>I personally think it is a problem with my
own laptop that Athena column window, which
we use to choose the corresponding nominator and >denominator
cannot be shown, or may be hidden somewhere else. This led
to unsuccessful importing data in my case, therefore, it showed
the red >message "You have not used any memory yet" and
program cannot be closed.
The Athena data import window seems to have a set size when
running in Windows (I don’t know about other platforms) and if your
screen isn’t big enough or you resolution is too low, then the “OK”
and “Cancel” buttons will be hidden below the Windows taskbar.
As such you won’t be able to import the data, and Athena will display the
message in red you got at the bottom, have the hourglass cursor, and you can’t
close it. Try changing the resolution if you can, or moving the taskbar, or
moving the data import window as high up your screen as you can. Then you
should be able to see and click the import button and process your data on your
laptop.
Hope this helps,
Steve
Stephen Price
Russell Group
Department of Chemistry
University of Southampton
Highfield
Southampton
SO17 1BJ
Ext: 24104
Tel: 02380 594104
From: ifeffit-bounces@millenia.cars.aps.anl.gov
[mailto:ifeffit-bounces@millenia.cars.aps.anl.gov] On Behalf Of NIRAWAT
THAMMAJAK
Sent: 06 September 2008 00:04
To: Bruce Ravel; XAFS Analysis using Ifeffit
Subject: Re: [Ifeffit] A problem with Athena
Bruce,
Please accept my apologies for a lack of
sufficient information in above email. I have tried to install program in
other computer and import those data files, I found that it worked properly as
usual!!
I am trying to figure out my laptop problem.
Anyway, I gratefully thank for your attempt to assist my
difficulties.
Nirawat.
2008/9/3 Bruce Ravel <bravel@bnl.gov>
On Wednesday 03 September 2008
15:20:31 you wrote:
> Thank you for your prompt response. I tried to import weird format files,
> Athena shown a box that said it cannot open those file. It is different
> from the problem I mentioned above that there was no any box, it just
> posted with a red messege in the bottom that 'You have not used any memory
> yet'. I tried with Athemis prj file, too. There was also a box said it
> cannot open because it seems to be an artemis file. And one more thing,
> once that red messege appeared, I cannot close Athena window anymore - it
> seems non-response for closing. Before this, It could open all of these
raw
> data files. But, now it happens to me very strange. However, it can
> normally import Athena project files, just only the project files, that I
> have worked and saved.
As I often say here on the list, I cannot fix a problem that
I cannot
replicate on my own computer. What you are describing is completely
unfamiliar to me. Unless you can give me an example file to replicate
what you are seeing, I won't be able to help you very much.
B
--
Bruce Ravel ------------------------------------ bravel@bnl.gov
National Institute of Standards and Technology
Synchrotron Methods Group at NSLS --- Beamlines U7A, X24A, X23A2
Building 535A
Upton NY, 11973
My homepage: http://xafs.org/BruceRavel
EXAFS software: http://cars9.uchicago.edu/~ravel/software/exafs/
_______________________________________________
Ifeffit mailing list
Ifeffit@millenia.cars.aps.anl.gov
http://millenia.cars.aps.anl.gov/mailman/listinfo/ifeffit
--
Nirawat Thammajak
Research and Academic Division,
National Synchrotron Research Center,
PO Box 93, Nakhon Ratchasima 30000 Thailand.
Tel. (+66) 044-217040 ext. 504
Fax (+66) 044-217047